机电控制无级变速器执行机构动态响应特性仿真研究

为研究夹紧力可调的机电控制无级变速器（EMCVT）电控电动执行机构的可靠性，及其速比和从动带轮夹紧力动态响应的影响因素，采用MATLAB/Simulink构建了EMCVT执行机构的动力学模型，设计了针对EMCVT电控电动执行机构的速比和夹紧力闭环控制器。对EMCVT输入转矩突变和目标速比突变两种工况进行了仿真分析，仿真结果表明：速比和从动带轮夹紧力动态响应的超调量和调节时间满足CVT的使用要求，从动带轮夹紧力响应时间小于1s，速比变化率可以达到2；EMCVT速比和从动带轮夹紧力动态响应的主要影响因素是执行电动机的负载和转动方向。     

Stability and thermophysical properties of fly ash nanofluid for heat transfer applications

Improving the performance of heat transfer fluids is altogether significant. The best approach for improving the thermal conductivity is the addition of nanoparticles to the base fluid. In the present study, specific heat, dynamic viscosity, and thermal conductivity of water-based Indian coal fly ash stable nanofluid for 0.1% to 0.5% volume concentration in the temperature range of 30 to 60°C has been investigated. To evaluate an average particle diameter of 11.5 nm, the fly ash nanoparticles were characterized with scanning electron microscopy and dynamic light scattering. Using zeta potential, the stability of nanofluid in the presence of surfactant Triton X-100 was tested. Thermal conductivity and viscosity of fly ash nanofluid increased, while specific heat decreased as volume concentration increased. The effect of temperature on the fly ash nanofluid was directly proportional to its thermal conductivity and specific heat and inversely proportional to viscosity.     

Photoluminescence and temperature sensing of lanthanide Eu3+ and transition metal Mn4+ dual-doped antimoniate phosphor through site-beneficial occupation

For a long time, rare-earth ion-doped phosphors have been widely used in temperature sensing because of their excellent light-emitting properties. However, most of the rare earth elements are relatively rare and expensive, so the transition group elements that are economical and easy to obtain have been favored by researchers. This paper presents a new type of phosphor doped with rare earth ion and transition metal for optical temperature measurement. In recent years, Mn⁴⁺-doped phosphors have attracted wide attention because of their strong deep red light-emitting properties. La₂LiSbO₆ provides a good host environment for Mn⁴⁺ and Eu³⁺ due to its unique crystal structure. In this paper, a series of La₂LiSbO₆ phosphors singly doped with Mn⁴⁺ and Eu³⁺, and co-doped with Eu³⁺/Mn⁴⁺ were synthesized. The crystal phases and optical properties of these materials were characterized and analyzed in detail. We specifically studied the temperature dependence of the fluorescence intensity of the optimized La₂LiSbO₆: Eu³⁺, Mn⁴⁺ phosphors at 303K–523K. The experimental results prove that the thermal responses of Mn⁴⁺ and Eu³⁺ are different. With increasing temperature, the thermal quenching of the Mn⁴⁺ fluorescence intensity is much faster than that of Eu³⁺, so the temperature characteristics can be explored by the fluorescence intensity ratio (FIR) of Eu³⁺ to Mn⁴⁺. At 523 K, its maximum relative sensitivity and maximum absolute sensitivity can reach 0.891% K⁻¹ and 0.000264 K^-1, respectively. Our experimental analysis shows that La₂LiSbO₆:Eu³⁺/Mn⁴⁺ phosphors have relatively high temperature sensitivity and have potential application prospects in the field of high temperature sensing.     

Study on chaotic oscillator-based algorithm for weak GLONASS signal acquisition

According to the characteristics of the chaotic oscillator in detecting weak signals, an algorithm based on Duffing chaotic oscillator array was proposed for acquisition of weak GLONASS signals. By means of GLONASS intermediate frequency and Duffing chaotic oscillator models, Lyapunov exponent is adopted to judge the critical condition of phase track and decide whether GLONASS signals exist or not by the change of the critical condition, and numeric iteration procedure is used to calculate the exponent. Finally, the performance of algorithm is simulated using GLONASS intermediate frequency data. The results indicate that acquisition algorithm can satisfy the need of object positioning in low signal-to-noise ratio environment.     

伞帽用高铬铸铁在热强碱腐蚀环境下的磨损分析

针对氧化铝行业中常用的Cr28和Cr20高铬铸铁伞帽在相同工况条件下的磨损机理进行分析,并对比研究了实际生产中两种失效材料的成分、组织及性能。结果表明,伞帽部件在高温强碱腐蚀条件下受到外界冲刷时,磨损量由微切削磨损与变形磨损这两种机制共同决定。含铬量较高的Cr28高铬铸铁,其冲刷和抗腐蚀磨损性能均优于Cr20高铬铸铁。伞帽服役寿命主要受浆料和表层的铸铁材料两大因素影响。两种试验材料经淬火+回火处理后,基体组织中主要为回火马氏体+M₇C₃型碳化物+少量残留奥氏体,其中含铬量较高的Cr28高铬铸铁中共晶碳化物含量更高,且分布更加弥散,其平均硬度值为64.0 HRC,高于Cr20高铬铸铁的60.2 HRC。最终确定Cr28高铬铸铁作为伞帽材质更能满足氧化铝生产及设备检修周期的需要。     

Nature inspired 21 branches sneezewort/Achillea ptarmica plant growth pattern–shaped antenna for Ku‐band applications

This reported paper presents the design and analysis of wideband nature inspired planar antenna of 46 × 18 × 1.6 mm³ size, designed using FR4 (Flame Retardant) substrate. The antenna patch is delineated from the growth pattern of sneezewort plant with supplementary notion of golden ratio in branching and branch width. The total number of branches in each stage follows the Fibonacci series and the branch width is calculated from the golden ratio concept. Starting from one feed line and two branches, the maximum numbers of branches are increased to 20. There has been significant enhancement in the radiation performance of proposed geometry by increasing the number of branches to 21 and by modifying ground with T‐shaped slot. The antenna covers wide impedance bandwidth of 8.2 to 16.5 GHz by possessing stable radiation characteristics.     

1 200 MPa级冷轧先进高强钢轧制稳定性的分析及控制

针对1 200 MPa级冷轧先进高强钢轧制不稳定问题,对热轧原料组织性能均匀性、冷轧压缩比、冷连轧机组轧制策略等进行了分析。结果表明,热轧工序投入边部加热器,采用分段冷却等手段,可有效降低热轧原料头尾部组织性能差异,保证通卷性能均匀,进而保证通卷轧制过程稳定;通过优化冷连轧机组压缩比,可有效降低材料本身的加工硬化强度,进而避免连轧机组后面机架的轧制超负荷情况;通过优化冷连轧机组轧制策略,可保证轧制过程中各机架均匀变形,避免出现轧制力差异较大的情况,进而保证轧制过程稳定。采用上述措施,1 200 MPa级冷轧先进高强钢轧制力控制在约15 000 kN,厚度精度控制在±0.06 mm以内,可保证该级别高强钢的稳定轧制。     

Effect of C/Ti ratio on densification,microstructure and mechanical properties of TiCx prepared by reactive spark plasma sintering

Titanium carbide (TiC) has been widely used as reinforcement in metal matrix composites and is known to exist over a wide range of stoichiometry. In this study, the effect of C/Ti ratio on the densification kinetics, grain size, lattice parameter, hardness and elastic modulus of TiC_x prepared by reactive spark plasma sintering (RSPS) is presented. Commercial purity titanium was ball milled with 5, 7.5, 10, 12.5, 15 and 17.5 wt% carbon black powder for 5 h and subjected to RSPS to prepare TiC_x samples with different C/Ti ratio. Dense TiC_x samples with ‘x′ ranging from 0.34 to 0.78 could be prepared by RSPS at 1400 °C. Increasing C/Ti ratio was found to increase the activation energy thereby reducing the rate of sintering and also resulted in finer grain size. The lattice parameter and the ratio of intensities of (200) to (111) peaks were correlated with the C/Ti ratio. The hardness and elastic modulus were shown to increase significantly with increase in C/Ti ratio.     

Milk from cows fed a diet with a high forage:concentrate ratio improves inflammatory state,oxidative stress,and mitochondrial function in rats

Excessive energy intake may evoke complex biochemical processes characterized by inflammation, oxidative stress, and impairment of mitochondrial function that represent the main factors underlying noncommunicable diseases. Because cow milk is widely used for human nutrition and in food industry processing, the nutritional quality of milk is of special interest with respect to human health. In our study, we analyzed milk produced by dairy cows fed a diet characterized by a high forage:concentrate ratio (high forage milk, HFM). In view of the low n-6:n-3 ratio and high content of conjugated linoleic acid of HFM, we studied the effects of this milk on lipid metabolism, inflammation, mitochondrial function, and oxidative stress in a rat model. To this end, we supplemented for 4 wk the diet of male Wistar rats with HFM and with an isocaloric amount (82 kJ, 22 mL/d) of milk obtained from cows fed a diet with low forage:concentrate ratio, and analyzed the metabolic parameters of the animals. Our results indicate that HFM may positively affect lipid metabolism, leptin:adiponectin ratio, inflammation, mitochondrial function, and oxidative stress, providing the first evidence of the beneficial effects of HFM on rat metabolism.     

Design and Fabrication of Concentration‐Gradient Generators with Two and Three Inlets in Microfluidic Chips

A simple and low‐cost method for designing and fabricating concentration‐gradient generators with two and three inlets is proposed which can generate different concentration gradients at varying flow velocities. The microchannel structure was designed in S‐shape and left‐right symmetry. The concentration‐gradient generator was simulated based on the finite element method. The microchannels were processed on a computer numerical control (CNC) engraving and milling machine on poly(methylmethacrylate) substrate, and then two concentration‐gradient generators were fabricated by hot bonding technology. The results of experiment and simulation were compared to prove the feasibility of the method. Flow velocity was an important factor for generating different concentration gradients. The concentration‐gradient profiles of the generators with two and three inlets present approximately linear and quadratic curves.